ZVex - Tremolo Probe ręcznie malowany

1378,00 PLN
Model: 505
Realizacja zamówienia: 3 dni
Producent: Zvex
   
Zvex Tremolo Probe jest pewnego rodzaju skrzyżowaniem pomiędzy kontrolą głośności theremina i Super Hard-On. Efekt ten posiada miedzianą płytkę zamontowaną w twardej obudowie z przezroczystego plastiku. Pod spodem jest płytka z aluminium odpowiedzialna za ekranowanie oraz zabezpieczenie gałek przed uszkodzeniem jeśli przypadkiem upuścisz efekt...jeśli upuścisz go na gołą stopę, może też obciąć Ci palce więc, UWAGA: NIE UPUSZCZAJ TREMOLO PROBE NA STOPĘ. JEST CIĘŻKI I MA OSTRE KRAWĘDZIE, KTÓRE MOGĄ USZKODZIĆ ŻYWE ISTOTY ORAZ PODŁOGĘ.

Ale do rzeczy. Co ten efekt robi?

Sercem Tremolo Probe jest układ znany z Super Hard-On połączony z kontrolerem w stylu theremina. Możesz stukać w kontroler stopą by uzyskać efekt tremolo będący w doskonałej synchronizacji z ruchem stopą. Możesz też korzystać z Trem Probe'a do volume swellów czy innych podobnych efektów.

Jak korzystać z efektu?

You might start with these settings and rules: 1) Plug in your cords (output and battery switch is on LEFT). 2) Make sure your guitar cords are AWAY from the antenna. They will mess with the probe just like your foot does. 3) Stomp on the switch and you'll be able to tell when it's on, when it is quiet with your foot away. Bring your foot near the antenna to control the volume of the guitar. 4) Put your foot completely on the pedal and adjust the knob on the back until it's at the right volume. Voila. DON'T MESS WITH THE SCREWDRIVER ADJUSTMENT SETTINGS UNDER THE PEDAL. Now that I said that, half of you will run for a screwdriver. Just remember this: use a bright light first and MARK the original settings. The white screwdriver slots have a light arrow imprinted on them... really, they do, look closer. Use a pin or sharp tool or sharpie and scratch or mark the metal where the original setting is before you goof around with the controls. Turning the controls in the direction of the arrows INCREASES the sensitivity of the antenna. DO NOT turn up the LED control to the top and leave it there. All that will do is drain your battery. In case you want to reduce the sensitivity, turn the RF control in the opposite direction from the arrow and you can make the plate respond only when your foot is in contact with it. If you are careful, you can adjust it so that the sensitive range goes from just touching it to putting your weight on it. How does the pedal get adjusted at the factory? First, I put the maximum volume setting exactly in the middle, straight up. Then I put the led adjustment in the middle (straight up and down) and then, holding it away from everything and keeping everything away from the antenna, I adjust the RF setting in the direction of the arrow until I can just hear a strummed guitar... then I keep strumming and turn it back until the guitar JUST disappears. This is a good setting for the tremolo and swell functions. Changing the battery: Take out the screws on the bottom of the painted part of the pedal. The entire bottom plate will lift away. Look at the way the battery is placed... the clip goes toward that little RF board with the blue thingies on it. Take out the old one and put in an ALKALINE. Because, it sounds just as good as that cheap offshore battery I gave you with the unit, and will last a lot longer with the LED thingie eating it alive. By the way, when your foot is off the pedal, if the led is off, the battery will last a long, long time. Most of the battery life is lost when the LED is BRIGHT. The Super Hard-On draws very little power. REMEMBER THAT THE BATTERY SWITCH IS ON THE LEFT, NOT THE RIGHT, SO UNPLUG THE OUTPUT CORD TO SAVE YOUR BATTERY.

W naszej ofercie znajdziesz także profesjonalne zasilacze pozwalające zasilić od 1 nawet do 20 efektów oraz złączki do efektów Dimarzio! Zamów za jednym razem i płać tylko raz za przesyłkę!!!

W razie jakichkolwiek pytań - prosimy o kontakt, chętnie pomożemy!